1004,West-CBD,No.139 Binhe Rd,Futian District,Shenzhen, China Post Code:518048
+86-18682200597
sales@szhaiwang.com
HW-N9MW The company launched the first dual-plate microwave sensor module, its appearance is beautiful, the product circuit structure is simple and compact, stable performance and affordable, its cost-effective and high, especially suitable for intelligent appliances, security products, lighting products and other Secondary development in the field of electronics. This product can be widely used in security monitoring, intelligent control systems, lighting appliances (garage, corridors, roads and other places).
1. Product Overview
HW-N9MW The company launched the first dual-plate microwave sensor module, its appearance is beautiful, the product circuit structure is simple and compact, stable performance and affordable, its cost-effective and high, especially suitable for intelligent appliances, security products, lighting products and other Secondary development in the field of electronics. This product can be widely used in security monitoring, intelligent control systems, lighting appliances (garage, corridors, roads and other places).
2. Product working principle:
The HW-N9MW microwave sensor module uses a planar antenna to send and receive high-frequency electromagnetic waves according to the principle of Doppler effect, and then detects micro-movement of the folded wave and then triggers the microprocessor to work. Finally, the OUT terminal outputs 3V effective high-power. Flat signal.
3. Product features:
Professional planar microstrip antenna design, field-shaped transmission and reception signals, wide coverage, high consistency, low power consumption, ROHS environmental protection, and strong anti-interference ability, not affected by temperature, humidity, air flow, dust, noise, light and dark . When the product is used indoors, the induction effect is better; when used outdoors, due to the influence of the environment, there is a phenomenon that the sensing distance is slightly reduced or the sensitivity is slightly weaker. This is a normal phenomenon, and the user does not need to question the product.
4. Induction time:
The default repeatable trigger: If the trigger signal is triggered again in the sensing area after the first trigger of the output signal, the module delay time will be added again when the first trigger time is not stopped. (For example, the module trigger time is 2S, and it is accepted again in 2S. To the sensing signal, once again superimposed 2S, there will always be an output signal when there is no nonstop trigger.) Non-repetitive trigger: The sensor triggers once, no time superimposed (for example: time 2s, trigger once, output 2s, within 2s Regardless of multiple triggers as invalid, time does not stack once for 2 seconds.
5. Product Specifications:
Products | HW-N9MW | ||
Operating Voltage | DC-3.7V-24V | Built-in 7533 regulator | |
Static power | <3MA Without load | Moving 3MA | Static 2.7mA |
Load output method | No direct load 3V-3mA | Inductive output high 3v, no induction low 0v. | |
Induction method | Doppler induction principle. Electromagnetic waves form a detection area and detect moving objects. | ||
Trigger method | Moving objects can be triggered repeatedly by default | ——Cannot be changed and cannot be triggered repeatedly | Note: If you need to not repeat the trigger, you need to customize. |
delay | Default 2s repeatable trigger | The time can be defined according to customer requirements. R2=Time 4.7K | |
Blocking time | No lock by default | customizable | Can be defined according to customer requirements. |
Frequency | Active radiation electromagnetic wave signal center frequency 3.2G. | ||
Sensing distance | Default 10 meters | The distance can be defined according to customer requirements. R5=Distance resistance 1M (150K-2M) | |
Operating temperature | -20-70℃ | Customizable | Advise to stay away from heat |
Dimensions | size=L23*W22*D8 mm | Long X Wide X High | mm |
6.Product test wiring diagram and CAD drawing
As shown in the figure, VCC can supply DC-3.7V-24V, JP is N9MW output port, 2 middle output high signal, when 2 pin output high, NPN tube 8050 conduction, VCC will provide power for the LED, this When the LED is on, it indicates that the module has a signal output. When there is no signal output on pin 2, the output is no signal state 0V. If you want to test the performance of this product, you can individually wire according to the above figure. This signal can be used later to trigger: trigger circuit - MOS tube - SCR - Relay - MCU and so on
7. Angles and Radiation Patterns
As shown in the figure: The reference map is derived from the measuring instrument. The actual sensing area is in accordance with the indoor 100 square meter angle range. Due to the close relationship between Doppler radar microwave and space, the practical application needs to define the detection range and angle according to the application environment (the smaller the microwave detection range space is, the higher the sensitivity is, and the larger the space is, the higher the sensitivity is attenuation). This figure serves as an official guideline for reference. Practical applications need to be checked according to the use environment.
8.Products picture
9. Note:
●About the installation process requirements of the product When installing and testing the product and actual assembly, please be sure to keep at least 10mm in front of the antenna board (S-shaped hole PCB) of the module product. Never touch or touch the plane of any object, or the product will not work properly.
● About power
It is recommended to use a qualified DC power supply, that is, the output voltage, current and ripple coefficient are all up to the standard DC power supply, otherwise it will affect the stability of the product, there may be some abnormalities, such as: false positives, no induction , Cycle from Kai, etc.
● About false positives
1, to ensure the power of the eligibility, please refer to the above first item;
2, When testing, ensure that there is no moving object (in the sensing range) around the product to be tested.
3, After power on, there is about 10s initialization time. During this period, it belongs to non-normal induction, which may cause false alarm false image;
4, when the indoor test, the induction is relatively sensitive, the surrounding needs to remain static, and to ensure that the first induction signal cycle is completed after the next test; outdoor test, be sure to pay attention to the dynamic environment of the surrounding environment, such as birds, Pedestrians, traffic, etc.
5, The signal current output by this module is very weak. When the load is directly driven, it may cause false alarms. Please be sure to refer to the application diagram of this product.
● Adjustment of work delay
A [time] resistor (R2) is soldered on the back of the module to change the delay time. The larger the resistance, the longer the delay.
● Adjustment of sensing distance
There is a [distance] resistor (R5) on the back of the module to convert the sensing distance. The greater the resistance, the greater the distance. Adjustable resistance range is 150K-2M.
Note: If the resistance value is greater than 2MΩ, it will make the circuit unstable! Customers are advised not to change this resistor by themselves. If necessary, please contact our relevant staff.
● The shell assembly of this product
The metal shell is not easily penetrated by microwaves and infrared rays, so this product should be avoided from being used in a metal shell. However, barriers such as plastics, ceramics and woody soils have better penetration effects. Specific circumstances, please take the test as the standard.
● The product's mutual harmonicity
This product has a certain degree of mutual resonance interference, so within the effective sensing range, try to avoid installing two or more modules face to face, otherwise it may affect your use of results. When necessary, please be sure to contact our relevant staff.
Product Specifications:
Products | HW-N9MW | ||
Operating Voltage | DC-3.7V-24V | Built-in 7533 regulator | |
Static power | <3MA Without load | Moving 3MA | Static 2.7mA |
Load output method | No direct load 3V-3mA | Inductive output high 3v, no induction low 0v. | |
Induction method | Doppler induction principle. Electromagnetic waves form a detection area and detect moving objects. | ||
Trigger method | Moving objects can be triggered repeatedly by default | ——Cannot be changed and cannot be triggered repeatedly | Note: If you need to not repeat the trigger, you need to customize. |
delay | Default 2s repeatable trigger | The time can be defined according to customer requirements. R2=Time 4.7K | |
Blocking time | No lock by default | customizable | Can be defined according to customer requirements. |
Frequency | Active radiation electromagnetic wave signal center frequency 3.2G. | ||
Sensing distance | Default 10 meters | The distance can be defined according to customer requirements. R5=Distance resistance 1M (150K-2M) | |
Operating temperature | -20-70℃ | Customizable | Advise to stay away from heat |
Dimensions | size=L23*W22*D8 mm | Long X Wide X High | mm |
szhaiwang4@hotmail.com
+86-18682200597
sales@szhaiwang.com